人与动物entrybaiducom为您找到"

aptr1h

"相关结果

In-Bulk-NAK Interrupt in FX1/FX2LP EP64093

EP64093 September 16, 2010 Document No. 001-64093 Rev. ** 3 Loopback Implementation The loopback is implemented in the TD_Poll function which is called repeatedly when the device is idle.
www.cypress.com/file/100821

Bare Minimum Isochronous Transfer Generic USB Device ...https://www.microchip.com/forums/m270049-p3.aspxAug 02, 2007 · I've searched the forum for a generic isoc transfer based example code but to no avail. I've done a bare minimum Isochronous Transfer Generic USB device port for PICKit 2 modified from the Microchip generic USB example. I have not yet fully understood the frame code yet so I choose the...

Aug 02, 2007 · I've searched the forum for a generic isoc transfer based example code but to no avail. I've done a bare minimum Isochronous Transfer Generic USB device port for PICKit 2 modified from the Microchip generic USB example. I have not yet fully understood the frame code yet so I choose the...
www.microchip.com/forums/m270049-p3.aspx

[故]ぶろぐhttps://ko-burogu.blogspot.com/2014/09/autoptrl...Translate this pageAPTR1H = MSB( &EP2FIFOBUF ); // Initializing the first data pointer APTR1L = LSB( &EP2FIFOBUF ); APTRnH,APTRLは、data pointerの始めの開始位置を指定するときに使う …

APTR1H = MSB( &EP2FIFOBUF ); // Initializing the first data pointer APTR1L = LSB( &EP2FIFOBUF ); APTRnH,APTRLは、data pointerの始めの開始位置を指定するときに使う …
ko-burogu.blogspot.com/2014/09/autoptrl...

USB Data Streaming Using Isochronous Endpoints

CE64263 September 3, 2013 Document No. 001-64263 Rev. *B 2 Operation Isochronous Transfers in USB In USB specifications, there are four types of transfers defined for varying needs of data communication.
www.cypress.com/file/123151

LoopBack fails for the second time - Embeddedrelatedhttps://www.embeddedrelated.com/showthread/comp.arch.embedded/...Hi, I am new to this group. I am using cypress fx2lp usb controller. I have written a loopback firmware for it and successfully downloaded on its ram. On the host side I have written an application which opens the usb device, send some data, read it back, verify and close the device. When I send ...

Hi, I am new to this group. I am using cypress fx2lp usb controller. I have written a loopback firmware for it and successfully downloaded on its ram. On the host side I have written an application which opens the usb device, send some data, read it back, verify and close the device. When I send ...
www.embeddedrelated.com/showthread/comp.arch.embed...

funwithfx2https://funwithfx2.wordpress.comBlogging after a week; Most of the work during last week was regarding working on the pull requests. I still dont think I have it nailed down. I would have to clean it up a lot more

Blogging after a week; Most of the work during last week was regarding working on the pull requests. I still dont think I have it nailed down. I would have to clean it up a lot more
funwithfx2.wordpress.com

EZ-USB 68013A开发指南 - 程序园 - voidcn.comwww.voidcn.com/article/p-gtyexejt-bq.htmlTranslate this pageaptr1h/aptr1h 通过 msb 和 lsb 获取 ep2fifobuf 的高位地址和地位地址。 EXTAUTODAT1 表示 APTR1H/APTR1H 指向的数据。 AUTOPTRH2/AUTOPTRL2 通过 MSB 和 LSB 获取 EP6FIFOBUF 的高位地址和地位地址。

aptr1h/aptr1h 通过 msb 和 lsb 获取 ep2fifobuf 的高位地址和地位地址。 EXTAUTODAT1 表示 APTR1H/APTR1H 指向的数据。 AUTOPTRH2/AUTOPTRL2 通过 MSB 和 LSB 获取 EP6FIFOBUF 的高位地址和地位地址。
www.voidcn.com/article/p-gtyexejt-bq.html

Slave fifo mode on cy68013a 56pin chip | Cypress …https://community.cypress.com/thread/23413Aug 10, 2012 · The follwing are based on slave fifo mode.I want to transfer the data to the EP0 ,then exchange the data between EP0 and EP6 under the vender command

Aug 10, 2012 · The follwing are based on slave fifo mode.I want to transfer the data to the EP0 ,then exchange the data between EP0 and EP6 under the vender command
community.cypress.com/thread/23413

Cypress CY7C68013A USB Bulk transfer problem - Keilwww.keil.com/forum/9849May 10, 2007 · Hi Frnds, I am using Cypress CY7C68013A EZ-USB micro controller, I have used BULKLOOP example given by cypress, where they have given a loop back transaction between EP2 to EP6, But I have changed the code for transmission of 64bytes of data as bulk on EP1, below code which i have written for bulk write …

May 10, 2007 · Hi Frnds, I am using Cypress CY7C68013A EZ-USB micro controller, I have used BULKLOOP example given by cypress, where they have given a loop back transaction between EP2 to EP6, But I have changed the code for transmission of 64bytes of data as bulk on EP1, below code which i have written for bulk write …
www.keil.com/forum/9849